Foundation Drainage Systems

No waterproofing system I know of is designed to work without proper drainage. Without relief, water can build up tremendous pressure underground. A waterproofing manufacturer won't warrant its product if drainage is missing or inadequate, or if the structure is built on a site where proper drainage is impossible.

Shop for waterproofing products & vapor barriers designed to protect your foundation.

The minimum drainage for any building is a perimeter footing drain. Depending on conditions, some buildings will require an underdrain system or a sump pit with a pump.

On this page:

• Ground Surface Treatment
• Foundation Drains
• Drainage Boards

Ground Surface Treatment

Old House Web

The ground at the top of the foundation wall offers the first line of defense against a wet interior space below. The more water that can be removed from the equation at the earliest opportunity, the better the total waterproofing or dampproofing system will function. This area is sometimes neglected but is crucial to success in both dampproofing and waterproofing.

This downspout discharges too close to the foundation.

A few simple procedures at the surface level are:

• Keep the water that comes off the roof from ending up in the basement by using a thorough gutter system. Collect the water in gutters and send it well away (10 feet at least) from the foundation wall in downspouts. Don't undersize either component-the smallest sizes clog easier and overflow quicker.

• Compact backfill in lifts next to foundation walls, otherwise it will settle over time and form a reverse slope, putting water where it's unwanted. However, be careful not to crush the drain pipe in the initial lift.

• Final grading should form positive drainage away from the house. The IRC requires a ½ inch per foot slope for at least 6 feet. Maintain this everywhere, through foundation steps and around corners.

• Some designs call for the use of downspouts discharging into 6-mil plastic pipes 6 inches below grade with the same positive slope to prevent excess surface water from percolating down. This is especially true in cold climates where heavy ice and snow on the roof preclude the use of gutter systems.

• Even properly graded and compacted surfaces can change over time, so the ground around the house may occasionally need to be re-dressed to account for settlement of the backfill.

• Trees, according to the Department of Housing and Urban Development, should be no closer to a foundation than their eventual height, otherwise tree roots can clog drains and can dry out soils enough to cause settlement.

• In areas where expansive soils are present, it is doubly important for structural reasons to prevent water from infiltrating under footings or slabs.

While there may be resistance to spending time and money on something a homeowner may never even see or think about again, it's best to do it correctly from the start. It's been said before, but it's never been more true than in this area of residential construction-it's much easier and cheaper to do it right the first time than to dig it up and fix it later.

Water Repellent Products Front-line technology produces an extensive line of water repellent products.

Waterproofing Rubber Coating Waterproofing elastomeric liquid membrane

HYDRALASTIC 836 Cold Applied, Single-component Waterproofing

Deep Penetrating Sealer RadonSeal - Free Shipping on 5-Gals.

Concrete Waterproofing Products Membranes – Coatings and More

Moisture Blocking Epoxy 4100 clear primer

Foundation Drains

Flexible drain pipe laid into a trench with plastic below and surrounded by gravel. Patterson Construction, Inc.

Drainage is a key element of any waterproofing or dampproofing system. Surface drainage is the first opportunity to mitigate water infiltration, but it is very difficult to keep all water away from foundation walls-both surface water and ground water can lead to problems. So it is very important not to use partial measures in draining water that ends up at the base of the foundation wall.

This 4-inch perforated drain pipe comes surrounded by
EPS aggregate and enclosed in polystyrene netting.
Ring Industrial Group

A typical sub-grade drainage system consists of:

• A layer of 6-mil plastic forming a trough in a trench at the bottom of the footing to capture as much water as possible
• A rigid or flexible 4-inch perforated drain pipe laid over the plastic and covered with clean well-graded gravel; some pipe is available with a sleeve to filter fines-this pipe should outlet to daylight, adequately drained soil, or a mechanically drained chamber (a sump)
• A covering of geotechnical filter fabric, as a barrier between the gravel and the backfill
• Backfill compacted in lifts to rough grade
• Finish grade sloped away from the wall

Strip drains, like this Form-A-Drain, double as stay-in-place formwork for the footing.CertainTeed Corp.

Here are a few things to keep in mind:

• Rigid drainage pipe, although more difficult to handle, may be preferable to flexible drain tile since it is easier to establish and maintain grade and avoid low spots where sediment can accumulate.
• Lay rigid drain pipe with the slots to the sides, which creates a continuous channel for water to run in but still allows rising ground water or water from above to easily get into the drain.
• Maintaining slope on a pipe may require it to be higher or lower than the footer in certain spots.
• Even a level pipe will move water if the outlet is lower than the bottom of the pipe.
• There are strip drains that lay against the outside edge of the footing. Some double as stay-in-place formwork for the footing. One example of this is Form-A-Drain which incorporates a double channel, one to use as the foundation drain and the other for radon mitigation or other ventilation, if needed. Brittleness in cold weather and deforming of the product in direct sunlight are potential problems.
• Not all subsurface water trickles from above. A rainstorm or melting snow miles away may end up sending a surge of water underground into a basement or crawl space.
• In very wet areas, an interior drainage collection pipe and trench and a sump pump can be employed to keep water under control.

Drainage Boards

Dimpled drain boards create a 1-inch air space next to the concrete foundation. Cosella Dorken Products

Another approach to waterproofing with applied sheet materials is to use drainage boards, with or without waterproofing on the concrete wall. These dimpled plastic sheets are available from several manufacturers and come in various length rolls, ranging from 4 feet to 9 feet 9 inches tall.

Drainage sheets come with an integral termination strip. Cosella Dorken Products.

The dimpled side is placed toward the foundation and holds the sheet about ½ inch from the wall. A termination strip is attached to the wall at the top. The plastic serves as a waterproofing membrane, keeping water from penetrating to the surface of the wall, and as protection for the membrane on the wall during backfilling. Any water that may get through (by condensation or leakage) can trickle down to the foundation drains through the space formed by the dimples.

Drainage boards cover the foundation from the ground level to the top of the footing. Cosella Dorken Products.

Different versions of this type of product have filter fabric attached to the dimpled side which is then installed away from the wall and forms the route for water to flow down to the drain. This gap can also serve to dry moisture that remains in the concrete wall from construction.

Some drainage boards incorporate solid materials that are porous enough to allow water to flow down while supplying some insulating value to the wall. Still others uses twisted or deformed wire covered with a filter fabric to provide the drainage space. There are lots of options for this component of the overall system.

Some additional points to consider:

• The dimpled drainage board can help reduce intermittent hydrostatic pressure because it moves water away before pressure can build against the foundation.
• A dampproofing coating is advisable behind drainage boards to prevent incidental moisture infiltration as long as it doesn't interfere with performance or the manufacturer's specifications.
• Some drainage panels, as part of overall systems, use specially designed drainage boards in combination with waterproofing membranes, to replace drain tile pipes (such as the Tremco system).